DC motors have high inductance, meaning that the current going over it will resist to change. When you turn off a pair of nmos, current will likely start flowing over the the other pair, from source to drain. Depending on the spec of your nmos, you may consider using diodes in parallel to nmos to carry this current. Obviously these diodes should be reverse biased during normal operation.
As you said before power on capacitor is discharged. Right after power on capacitor is still discharged, so voltage on capacitor is zero, so reset pin has Vcc. With time capacitor gets charges and voltage across capacitor increases and reset voltage becomes closer and closer to ground, until it is ground. But it is important to consider what happens at power down too. At power down capacitor is charged. If power source becomes high impedance at power down, then reset pin will probably go down to zero in time but may take a bit time depending on what source exactly does. But if power source is connected to zero at power down reset pin will observe minus vcc and slowly go up to 0. If reset pin is sensitive it may be a good idea to protect it with a diode.
Simpsons predicted it once again.
If you knew about the birds and the bees, you would know that this wasn’t random.
I don’t think this will work well and others already explained why, but thanks for using this community to pitch your idea. We should have more of these discussions here rather than CEO news and tech gossip.
We should stop calling these titles confusing and call them what they are, plain wrong. This is the title of the original article. People who cannot write grammatically correct titles are writing entire articles.
Depending on the power consumption, you may consider not using thermal relief while connecting thermal vias for the chip (component 57) to ground layers. But this may make soldering harder so do it only if needed. Thermal vias are so close that they form 3 long dents in 3v3 plane. It is good practice to put vias a little far apart so that planes can go through between vias. This can be important since sometimes lowest impedance can be obtained when current is flowing between those vias. If you don’t need to fit 15 vias there, you may consider reducing the number and separating them a bit. You can also check the design rules for minimum copper width and minimum via clearance for your manufacturer and enter them in your CAD tool.
I don’t realistically expect such ban to happen. I started banning everyone who posts about Musk instead, my feed got a lot cleaner.
Web design is not the only option for someone who likes programming. Since you are still a student, there are so many options in front of you. You can be an embedded engineer and work closer to hardware, design firmware, electronic chips themselves or their verification environment. You can be a software engineer and work on business-to-business software which does not include adds and is very useful (e.g. CAD tools, inventory trackers for supermarkets and hospitals etc.). There is so much you can do, pursue something you are enthusiastic about.
Is this an AOE2 reference or is it historically correct? I knew I should not have learnt history from games.
Are you writing from your grave?
Pointing out won’t do, we need moderation.
It may be early for crunchy leaves. Marinade them for another month for perfect crunchiness.
Thanks for not putting the paper behind a paywall!
In this article RTL refers to register transfer level. It is a way of describing hardware on very low level, it uses registers for memory (which usually translates to flip-flops when/if synthesized), wires, basic arithmetic and logic operations, but terminology may slightly change based on which rtl language is being used. It can be used to design a CPU, or any ASIC (application specific integrated circuit) chip. Instructions may resemble to processor instructions, but the end result is fundamentally different. You may run a set of instructions on a processor, while what rtl describes is often synthesized and becomes the hardware itself which performs the operations (e.g. arithmetic logic unit in the cpu).
That could actually be useful (IBD gang)
Hold a small piece of metal (paper clip?) between solder pads with a tweezer. Heat up tip of a metal fork/spoon (Sharp edge of fork could work better) on a stove. Take it from stove and use it immediately to melt the solder on one pad (seems like there is already enough solder there). I am not sure if it would work but maybe worth trying. Heating entire fork could be hard, so maybe something with smaller metal mass could work better, like a screwdriver, nail clipper etc).